EP-400 Epoxy Putty

RectorSeal EP-400 (4 oz.) epoxy putty is a pre-measured knead able reinforced epoxy putty stick that cures “steel-hard” within 15 to 20 minutes of mixing at room temperature (77 degree F). The epoxy is extremely tough and durable with exceptional adhesion to a wide range of surfaces

DESCRIPTION:

RectorSeal EP-200 (2 oz.) / EP-400 (4 oz.) epoxy putty is a pre-measured knead able reinforced epoxy putty stick that cures “steelhard” within 15 to 20 minutes of mixing at room temperature (77 degree F). The epoxy is extremely tough and durable with exceptional
adhesion to a wide range of surfaces.
Within an hour, it can be drilled, tapped, sanded, painted, filed or machined. It can be used to bond, seal, plug, mold or rebuild many
different surfaces. The epoxy is capable of withstanding temperatures up to 500 degree F and will even harden under water.


CHARACTERISTICS:

• Premeasured resins and • Can even harden under water • Conveniently available in both 2 ozs.
hardeners in one tube (EP-200) and 4 oz. (EP-400) sizes in a
neutral gray color
• Contains no asbestos • Pressure tested to 1300 psi • Permanent repair
• Easy to use – bonds, seals, • Can withstand temperatures
plugs, molds, and rebuilds continuously up to 500 degree F
• No special tools needed

APPLICATIONS: (Can be used on Steel, Wood, Aluminum, PVC, Fiberglass, Copper, Ceramics, Bronze, Iron)

RectorSeal EP-200 or EP-400 epoxy putty has a wide variety of uses in:
Plumbing: Pipes (copper, steel, PVC), Joints, Fixtures, Spas, Drains, Dishwashers, Water heaters, etc. A/C Heating: Ductwork, Unit
Bodywork, Fans/Blowers, etc. Electrical: Motor Housings, Shafts, Fixtures, etc. Industrial: Machinery, Pumps, Housings, etc. Automotive:
Gas Tanks, Engine Blocks, Fans, Mufflers, Oil Pans, Radiators, etc. Marine: Body Repair, Engine Repair, Ladders, Trim, Motors, etc.
Farm: Implements, Tools, Machinery, etc. Home: Furniture Repair, Hole Patching, Cabinets, Doors, Wood Repairs, Stripped Threads,
Appliances, etc.


INSTRUCTIONS:

1. Thoroughly clean surface to be repaired, removing any grit, grease, or paint. For best adhesion, roughen area with emery cloth,
sandpaper or file before applying.
2. Remove wrapper from putty and cut or break off enough for desired repair. Knead until mixture is one uniform color.
3. Apply at once. Shape, smooth and remove any excess putty before it hardens. Use a putty knife or fingers to press putty into any
cracks or depressions. Use within 2 or 3 minutes after mixing. At room temperature, putty will begin to harden in 3 to 7 minutes, sets
hard in 12 to 20 minutes and can be sanded, drilled, machined or filed in about one hour.
4. Wash hands with soap and water immediately after use.


SPECIFICATIONS:

Density 15.9 lb/gal (1.9 g/cc) Tensile Strength 6000 psi
Color Gray Compressive Strength 18.000 psi
Shelf Life 3 years Modulus of Elasticity 6 x 105 psi
Hardness (Shore D) 85 Shear Strength 700 psi
Temperatures Range 500 degree F continuous Izod Impact 0.3 ft lbs/in of notch
Dielectric Strength 400 volts/ mil @ 0.125 in
Volume Resistivity 5 x 105 ohm-cm